Connectors & Wiring

Premium genuine Panasonic FR-A 470µF 35V low-impedance aluminium electrolytic capacitors, supplied as a pack of five. Selected by Pure Drone following FPV product testing and evaluation as our preferred compact power-filtering capacitor for reliable 4S and 6S builds.Why FPV drones use a capacitorSoldered across the ESC battery input, the capacitor absorbs short voltage spikes and smooths high-frequency electrical noise produced by the ESC and motors. This can help protect connected electronics, reduce interference in the video feed and provide cleaner power to the flight controller, VTX and camera.Key benefits Low impedance and high ripple-current capability Helps suppress voltage spikes at the ESC battery input Can reduce electrical noise, video interference and power-related instability Compact 10 × 16mm radial package High-reliability Panasonic FR-A series Suitable for correctly installed 4S and 6S FPV builds Specifications Manufacturer: Panasonic Series: FR-A Manufacturer part number: EEUFR1V471 RS stock number: 708-3825 Capacitance: 470µF Rated voltage: 35V DC Maximum impedance: 28mΩ at 100kHz Rated ripple current: 1.79A at 100kHz Capacitance tolerance: ±20% Operating temperature: -40°C to +105°C Dimensions: 10mm diameter × 16mm long Lead pitch: 5mm Mounting: radial through-hole Construction: polarised aluminium electrolytic Country of origin: Malaysia Pack contents: 5 capacitors InstallationThis is a polarised component. The stripe on the body marks the negative terminal. Solder positive to battery positive and negative to battery negative, as close as practical to the ESC battery pads, with the leads kept short and insulated. Reversing polarity can cause the capacitor to fail or vent.A fully charged 6S LiPo is 25.2V, leaving nominal headroom below the capacitor's 35V rating. For unusually long battery leads or exceptionally severe transient conditions, a higher-voltage capacitor may be preferable.

The GEPRC Smoke Stopper is an inline current-protection tool for checking newly built or repaired FPV electronics before direct battery connection, with both XT30 and XT60 connectors.SpecificationsInput voltage: 1–6S LiPo / 3–30VTrip current: 1.0AHold current: 0.5AShort-circuit trip time: approximately 3msOvercurrent trip time: approximately 10msConnectors: XT30 and XT60, input and outputComponent weight: 13.6gImportantUse during initial power-up and fault checking. This is a current-protection aid and cannot prevent every type of electrical damage; correct wiring and continuity checks are still required.

Genuine AMASS male and female connector packs for FPV drones, RC models, LiPo batteries, ESCs, motors, chargers and workshop leads. Choose XT30U, XT60H, XT90H or MR30. Every option is supplied as a pack of five complete matching male-and-female connector pairs. XT60H, XT90H and MR30 packs also include the corresponding insulating rear covers.Choose the right connector XT30U: Compact two-pin connector for lightweight FPV and RC power wiring. AMASS rates the cable model to 20A maximum with 16AWG cable under its stated temperature-rise test condition. XT60H: Two-pin main-power connector with rear covers for medium-current battery and ESC installations. Rated to 35A maximum with 12AWG cable under the manufacturer’s test condition. XT90H: Larger two-pin connector for higher-current battery and ESC wiring. Rated to 45A maximum with 10AWG cable under the manufacturer’s test condition. This is the standard XT90H and is not the anti-spark XT90S. MR30: Compact three-pin connector for keeping brushless motor-to-ESC phase connections together. Rated to 20A maximum with 16AWG cable under the manufacturer’s test condition. Shared AMASS specifications 500V DC maximum voltage 100 mating cycles IP40 protection rating -20°C to +120°C working temperature UL94 V-0 flame-retardant housing Gold-plated contacts Solder termination Pack contents XT30U pack: 5 male connectors + 5 female connectors, forming 5 complete pairs XT60H pack: 5 male connectors + 5 female connectors + 10 rear covers, forming 5 complete pairs XT90H pack: 5 male connectors + 5 female connectors + 10 rear covers, forming 5 complete pairs MR30 pack: 5 three-pin male connectors + 5 three-pin female connectors + 10 rear covers, forming 5 complete pairs Installation and safetyThese are solder connectors and require competent installation. Confirm battery polarity before connection and confirm all three motor phases when fitting MR30. Use the appropriate cable gauge and a suitably powerful soldering iron so each joint is completed quickly without overheating the nylon housing. Fully insulate the soldered terminals, keep positive and negative conductors separated, and never solder with a battery connected.Current capability depends on cable gauge, solder quality, ventilation, ambient temperature and installation conditions. Do not exceed the rating of the cable or the weakest component in the power system.

Compact HGLRC LED Mini lighting options for FPV builds. Choose the LED Mini Controller for controlling compatible RGB lighting, or the lightweight 38mm RGB LED set for adding bright programmable lighting to your quad.Choose your typeLED Mini Controller 2–6S input (7.4–25V) One-click mode switching Reserved pads for LED connections Supports direct control and flight-controller/remote adjustment Electronic switch function Dimensions: 17 × 12.5 × 6.5mm Controller weight: 1.47g Included: 1 × LED Mini Controller and 4 × 30AWG 100mm connecting wires (red, black, yellow and green).LED Mini 38mm RGB Set – 4 Pack 5V input 12 × RGB2020 LEDs per strip Dimensions per strip: 38 × 7.1 × 5mm Weight per strip: 0.7g 70mm connection leads Compact, lightweight design for FPV builds Included: 4 × HGLRC LED Mini 38mm strips and 4 × connecting leads.