All Parts
Every product live in our Shopify store.
T-Motor F50 2207 2150KV & 2200KV Racing Motor Hobby
High-performance 2207 FPV motor for 5-inch racing and freestyle builds. Available in 2150KV and 2200KV versions for 6S setups. Designed for strong throttle response, high thrust and competitive 5-inch performance. Key features:• 2207 stator size• 6S compatible• 5 mm shaft• Lightweight construction• Suitable for racing and high-performance freestyle• Recommended with 5-inch tri-blade propellers Detailed specifications vary by KV version and are shown below.
T-Motor Hobby F60 Pro V 2207.5 2020KV Racing Motor
The T-Motor F60 Pro V 2020KV is a 2207.5 motor for high-power 5-inch FPV racing and freestyle builds on 5S or 6S. Specifications: Brand: T-MotorModel: F60 Pro VKV: 2020KVStator size: 2207.5Motor dimensions: 26.8 × 31.7mmWeight: 33.8g including cableRecommended battery: 6S 1300mAh 120CPeak current: 52.7A for 10 secondsMaximum power: 1,297W for 10 secondsMotor shaft diameter: 4mmPropeller mounting size: 5mmMotor lead: 20AWG, 150mmMotor configuration: 12N14PIdle current: 1.25ABearing: EZOPropeller size: 5-inch Package contents: 1 × T-Motor F60 Pro V motor4 × socket-head mounting screws1 × propeller locknut1 × shaft screw Confirm propeller, ESC and battery suitability for the complete build before use.
T-Motor Velox V2207 V3 1950KV & 2050KV FPV Motor
The T-Motor Velox V2207 V3 is a 2207 motor for 5-inch 6S racing and freestyle builds, available in 1950KV and 2050KV. Specifications: Brand: T-MotorModel: Velox V2207 V3Stator size: 2207KV options: 1950KV / 2050KVRecommended battery: 6S LiPoMotor dimensions: 27.5 × 31.8mmMotor configuration: 12N14PMounting pattern: 16 × 16mm, 4 × M3Internal shaft diameter: 4mmThreaded propeller shaft: M5Motor lead: 20AWG, 150mm 1950KV: Weight including cable: 37.1gIdle current at 10V: 1.32AMaximum power: 1,050.5W for 60 secondsPeak current: 45A for 60 seconds 2050KV: Weight including cable: 36.8gIdle current at 10V: 1.66AMaximum power: 1,153.4W for 60 secondsPeak current: 49.5A for 60 seconds Recommended setup: Frame size: 5-inch FPV quadcopterRecommended ESC family: T-Motor Velox V45A V2 4-in-1 ESCCompatible propeller families: T5143S, F5146, P49436 and T5147 Package contents: 1 × T-Motor Velox V2207 V3 motor1 × M5 propeller locknutMounting screws Confirm propeller, ESC and battery suitability for the complete build before use.
VCI 2207 Pro Yuki Edition 2110KV FPV Motor
The VCI 2207 Pro Yuki Edition is a high-performance brushless FPV motor designed for fast 5-inch racing and freestyle builds. Developed as the 2110KV Yuki Edition of the VCI 2207 Pro platform, it combines a lightweight 2207 stator with high-temperature materials and a strong 6S power system. Key features: • 2207 stator size• 2110KV winding• Designed for 6S LiPo• Suitable for 5-inch FPV quadcopters• 0.1mm Japanese silicon-steel stator laminations• 240°C enamelled winding wire• 7075 aviation-grade aluminium construction• TC4 titanium-alloy shaft components• N52SH curved magnets• Vibration-reducing damping ring• 12S14P motor configuration• 16 × 16mm mounting pattern• M5 threaded propeller shaft• 20AWG, 150mm motor leads Specifications: KV: 2110KVRated voltage: 6S LiPo, 24V nominalStator size: 2207Motor dimensions: 27 × 31.4mmWeight: 33.2g including cablePeak current: 50.27AMaximum instantaneous power: 1,206.48WIdle current at 10V: 1.0AInternal resistance: 54mΩMotor configuration: 12S14PMounting pattern: 16 × 16mm, 4 × M3Threaded propeller shaft: M5Shaft length: 12.2mmMotor lead: 20AWG, 150mmMagnets: N52SH curved magnets Recommended ESC: Use with a quality 6S ESC rated at least 55A per motor. A 60A 4-in-1 ESC is preferable for aggressive racing setups or high-load propellers. Package contents: • 1 × VCI 2207 Pro Yuki Edition motor• Mounting screws• M5 propeller nut Maximum performance depends on the selected propeller, ESC, battery and complete aircraft setup. Always confirm component compatibility before use.
DOGCOM 1380/1480mAh 180C 6S 22.2V FPV Racing LiPo Battery
The latest DOGCOM 180C 6S FPV racing LiPo battery replaces the previous 150C version with an upgraded extremely high-discharge specification. Choose between the lighter 1380mAh pack or the higher-capacity 1480mAh pack. Specifications Battery type: LiPoConfiguration: 6S1PNominal voltage: 22.2VContinuous discharge rating: 180CMaximum discharge rating: 360CDischarge connector: XT60Balance connector: JST-XHRApplication: 5-inch FPV racing and freestyle 1380mAh variant Capacity: 1380mAhEnergy: 30.64WhDimensions: 33 × 39 × 81mmWeight: approximately 209gDOGCOM reference: DC-0069 1480mAh variant Capacity: 1480mAhEnergy: 32.86WhDimensions: 36 × 39 × 81mmWeight: approximately 223gDOGCOM reference: DC-0070 Included 1 × DOGCOM 180C 6S FPV LiPo battery LiPo safety Charge only with a suitable balance charger. Never charge unattended. Do not use a swollen, punctured or damaged battery. Store at the correct storage voltage in a fire-resistant location.
DOGCOM 2200mAh 6S 150C LiPo Battery XT60
The DOGCOM 2200mAh 6S is a high-capacity, high-output LiPo battery designed for FPV and RC aircraft that require greater endurance than a typical racing pack. With a 150C continuous discharge rating and 300C burst rating, it is designed to provide strong power delivery under demanding loads. Its 2200mAh capacity is suited to larger FPV drones, long-range builds and aircraft where additional flight time is preferred over minimum battery weight. Key features: • 2200mAh capacity• 6S1P LiPo configuration• 22.2V nominal voltage• 150C continuous discharge rating• 300C burst discharge rating• Approximately 312g• Compact 44 × 34 × 105mm dimensions• Designed for high-output FPV and RC applications• Suitable for larger and endurance-focused builds Specifications: Capacity: 2200mAhCell count: 6SConfiguration: 6S1PNominal voltage: 22.2VContinuous discharge rating: 150CBurst discharge rating: 300CDimensions: 44 × 34 × 105mmWeight: approximately 312gManufacturer model: DC2200/150C-6S Package contents: • 1 × DOGCOM 2200mAh 6S 150C LiPo battery
Gemfan 5129.2 MinJae 5.1-Inch 3-Blade Propellers 4-Pack
The Gemfan 5129.2 MinJae is an ultra-lightweight 3-blade FPV racing propeller developed with Korean racing pilot Minjae Kim. 4-Pack Designed for technical race tracks, rapid direction changes and precise gate control, each propeller weighs only 4.12g. Its low rotational inertia provides sharp steering response and fast recovery while retaining the grip and control of a tri-blade design. Key features: • 5.1-inch racing propeller• 2.92-inch pitch• 3-blade design• Lightweight 4.12g construction per propeller• Approximately 10% lighter than conventional racing propellers• Reduced rotational inertia for quicker steering response• Durable polycarbonate construction• 5mm centre mounting hole• Optimised for 2207 motors• Designed for fast, technical FPV racing• Supplied as a set of four: 2 × CW and 2 × CCW Specifications: Manufacturer: GemfanModel: 5129.2 MinJaePropeller diameter: 130.3mm, approximately 5.1 inchesPitch: 2.92 inchesBlade count: 3Material: PolycarbonateWeight: 4.12g per propellerCentre thickness: 6.2mmCentre-hole diameter: 5mmMaximum blade width: 14.9mmRecommended motor size: 2207Recommended take-off weight: approximately 500gRotation supplied: 2 × clockwise and 2 × counter-clockwisePack quantity: 4 propellers Available colours: • Yellow• Purple• Pink Package contents: • 2 × clockwise Gemfan 5129.2 propellers• 2 × counter-clockwise Gemfan 5129.2 propellers Always check each propeller for cracks, distortion or impact damage before flight. Replace damaged propellers immediately and confirm the correct clockwise and counter-clockwise orientation before arming.
Gemfan MCK 51366 ReV3 5.1-Inch 3-Blade Propellers 4-Pack
The Gemfan Hurricane MCK 51366 ReV3 is a lightweight 3-blade FPV racing propeller developed with championship racing pilot MCK. 4-Pack The ReV3 uses a reduced 2.8-inch pitch for fast throttle response, strong acceleration and precise cornering control on technical race tracks. Its lightweight polycarbonate construction provides a balance of grip, speed and impact resistance for competitive 5-inch FPV racing. Key features: • 5.1-inch-class racing propeller• 2.8-inch pitch• 3-blade design• Lightweight 4.2g construction per propeller• Durable polycarbonate construction• Fast throttle response and strong punch• High cornering grip and precise control• 5mm centre mounting hole• Optimised for 2207 and 2306 motors• Designed for high-KV 6S racing setups• Supplied as a set of four: 2 × CW and 2 × CCW Specifications: Manufacturer: GemfanModel: Hurricane MCK 51366 ReV3Propeller diameter: 129.7mm, approximately 5.1-inch classPitch: 2.8 inchesBlade count: 3Material: PolycarbonateWeight: 4.2g per propellerCentre thickness: 6.6mmCentre-hole diameter: 5mmMaximum blade width: 14.9mmRecommended motor size: 2207 or 2306Rotation supplied: 2 × clockwise and 2 × counter-clockwisePack quantity: 4 propellers Available colours: • Strawberry Jam• Mint Green• Radioactive Yellow• Litchi Red Package contents: • 2 × clockwise Gemfan MCK 51366 ReV3 propellers• 2 × counter-clockwise Gemfan MCK 51366 ReV3 propellers Always inspect each propeller for cracks, distortion or impact damage before flight. Replace damaged propellers immediately and confirm the correct clockwise and counter-clockwise orientation before arming.
Gemfan Hurricane 51433 5.1-Inch 3-Blade Propellers 4-Pack
The Gemfan Hurricane 51433 is a lightweight 3-blade FPV propeller developed for smooth and responsive 5-inch freestyle flying. 4-Pack Its 5.1-inch diameter and 3.5-inch pitch provide a controlled, linear throttle response with enough power for technical manoeuvres, fast recoveries and flowing freestyle lines. Lightweight polycarbonate construction reduces rotational mass for rapid motor response while retaining the durability needed for regular freestyle use. Key features: • 5.1-inch freestyle propeller• 3.5-inch pitch• 3-blade design• Approximately 3.8g per propeller• Durable polycarbonate construction• Smooth and predictable throttle response• Lightweight design for quick motor response• 5mm centre mounting hole• Suitable for 2206 to 2306 motors• Designed for 5-inch FPV freestyle quadcopters• Supplied as a set of four: 2 × CW and 2 × CCW Specifications: Manufacturer: GemfanModel: Hurricane 51433Propeller diameter: approximately 129.7mm / 5.1 inchesPitch: 3.5 inchesBlade count: 3Material: PolycarbonateWeight: approximately 3.8g per propellerCentre thickness: 6mmCentre-hole diameter: 5mmMaximum blade width: approximately 14.3mmRecommended motor size: 2206 to 2306Rotation supplied: 2 × clockwise and 2 × counter-clockwisePack quantity: 4 propellers Available colours: • Pink• Yellow Package contents: • 2 × clockwise Gemfan Hurricane 51433 propellers• 2 × counter-clockwise Gemfan Hurricane 51433 propellers Always inspect each propeller for cracks, distortion or impact damage before flight. Replace damaged propellers immediately and confirm the correct clockwise and counter-clockwise orientation before arming.
Gemfan YUKI 5129 5.1-Inch 3-Blade Propellers 4-Pack
The Gemfan YUKI 5129 is a lightweight 3-blade FPV propeller designed for responsive 5-inch racing and fast freestyle builds. Pack of 4 Its 5.1-inch diameter and 2.9-inch pitch provide quick acceleration, precise throttle control and predictable handling at higher speeds. Durable polycarbonate construction combines low rotational weight with the resilience needed for regular FPV flying. Key features: • 5.1-inch FPV propeller• 2.9-inch pitch• 3-blade design• Approximately 4.5g per propeller• Durable polycarbonate construction• Responsive acceleration and precise throttle control• 5mm centre mounting hole• Suitable for 2207 and 2306 motors• Intended for 500–600g FPV quadcopters• Suitable for racing and fast freestyle• Supplied as a set of four: 2 × CW and 2 × CCW Specifications: Manufacturer: GemfanModel: YUKI 5129Propeller diameter: 129.7mm, approximately 5.1 inchesPitch: 2.9 inchesBlade count: 3Material: PolycarbonateWeight: approximately 4.5g per propellerCentre thickness: 6.1mmCentre-hole diameter: 5mmMaximum blade width: 14.7mmRecommended motor size: 2207 or 2306Recommended take-off weight: 500–600gRotation supplied: 2 × clockwise and 2 × counter-clockwisePack quantity: 4 propellers Available colours: • Blue• Pink• Purple• Yellow Package contents: • 2 × clockwise Gemfan YUKI 5129 propellers• 2 × counter-clockwise Gemfan YUKI 5129 propellers Always inspect each propeller for cracks, distortion or impact damage before flight. Replace damaged propellers immediately and confirm the correct clockwise and counter-clockwise orientation before arming.
Gemfan Hurricane 51377 MAX 5.1-Inch 3-Blade Propellers 4-Pack
The Gemfan Hurricane 51377 MAX is a reinforced 3-blade FPV racing propeller designed for modern high-output 5-inch competition builds. Its 5.1-inch diameter and 3-inch pitch provide responsive acceleration, stable power delivery and predictable grip through gates and fast corners. Reinforced high-stress areas improve impact resistance, helping the propeller retain its shape after minor contact during racing. Key features: • 5.1-inch racing propeller• 3-inch pitch• 3-blade design• Approximately 4.5g per propeller• Reinforced high-stress areas• Durable polycarbonate construction• Responsive acceleration• Stable and predictable power delivery• 5mm centre mounting hole• Optimised for 2207 2100KV motors and similar racing setups• Designed for competitive FPV racing and high-speed track flying• Supplied as a set of four: 2 × CW and 2 × CCW Specifications: Manufacturer: GemfanModel: Hurricane 51377 MAXPropeller diameter: 129.7mm, approximately 5.1 inchesPitch: 3 inchesBlade count: 3Material: PolycarbonateWeight: approximately 4.5g per propellerCentre thickness: 6.1mmCentre-hole diameter: 5mmMaximum blade width: 14.7mmRecommended motor: 2207 2100KV or similar racing setupRotation supplied: 2 × clockwise and 2 × counter-clockwisePack quantity: 4 propellers Available colours: • Macho Pink• Neon Yellow Package contents: • 2 × clockwise Gemfan Hurricane 51377 MAX propellers• 2 × counter-clockwise Gemfan Hurricane 51377 MAX propellers Always inspect each propeller for cracks, distortion or impact damage before flight. Replace damaged propellers immediately and confirm the correct clockwise and counter-clockwise orientation before arming.
SEQURE Blueson A1 6S 65A AM32 4-in-1 ESC
The SEQURE Blueson A1 6S 65A is a 4-in-1 ESC with AM32 firmware for 2–6S LiPo and LiHV FPV builds. It uses an AT32F421 32-bit processor with an adjustable 8–128kHz PWM frequency. Telemetry and current sensing are supported, with a 20 × 20mm M3 mounting pattern. Specifications ESC type: 4-in-1Firmware: AM32Processor: AT32F421Input voltage: 2–6S LiPo or LiHVContinuous current: 65A per channelPeak current: 120A per channelPWM frequency: 8–128kHzMotor protocols: DShot150, DShot300, DShot600, OneShot, MultiShot and PWMTelemetry: SupportedCurrent sensing: SupportedBEC: NoneMounting pattern: 20 × 20mm, M3Dimensions: 42.5 × 36 × 7mmProduct weight: Approximately 19g Included 1 × SEQURE Blueson A1 4-in-1 ESC1 × 30AWG 40mm reverse double-ended SH1.0-8P cable1 × 30AWG 60mm single-ended SH1.0-8P cable2 × 12AWG 100mm power cables, red and black1 × XT60H-M male connector1 × 35V 680µF solid capacitor5 × M3 × 8mm shock-absorbing mounts Important This ESC does not include a BEC. Check the power requirements of the flight controller, receiver and video system before installation. Use the supplied capacitor and appropriately rated battery cable and connectors. Confirm firmware settings, motor direction and failsafe operation before fitting propellers.
SEQURE Blueson A1 8S 70A BLHeli_32 4-in-1 ESC
The SEQURE Blueson A1 8S 70A is a 4-in-1 ESC with BLHeli_32 firmware for 2–8S LiPo and LiHV FPV builds. It uses an AT32F421 32-bit processor with an adjustable 8–128kHz PWM frequency. Telemetry and current sensing are supported, with a 20 × 20mm M3 mounting pattern. Specifications ESC type: 4-in-1Firmware: BLHeli_32Processor: AT32F421Input voltage: 2–8S LiPo or LiHVContinuous current: 70A per channelPeak current: 150A per channelPWM frequency: 8–128kHzMotor protocols: DShot150, DShot300, DShot600, OneShot, MultiShot and PWMTelemetry: SupportedCurrent sensing: SupportedBEC: NoneMounting pattern: 20 × 20mm, M3Dimensions: 42.5 × 36 × 7mmProduct weight: Approximately 19g Included 1 × SEQURE Blueson A1 4-in-1 ESC1 × 30AWG 40mm reverse double-ended SH1.0-8P cable1 × 30AWG 60mm single-ended SH1.0-8P cable2 × 12AWG 100mm power cables, red and black1 × XT60H-M male connector1 × 35V 680µF solid capacitor5 × M3 × 8mm shock-absorbing mounts Important This ESC does not include a BEC. Check the power requirements of the flight controller, receiver and video system before installation. Use the supplied capacitor and appropriately rated battery cable and connectors. Confirm the firmware settings, motor direction and failsafe operation before fitting propellers.
Droneframes MS25 FPV Racing Frame Set
The Droneframes MS25 is a lightweight FPV racing frame available with V2 or V3 arms. Compared with the MS24, the MS25 uses tighter prop-to-prop spacing across the roll axis, revised carbon cutouts and refined frame geometry. The interlocking arm system allows an individual arm to be replaced by removing a single screw. Specifications Frame type: FPV racing frameArm versions stocked by Pure Drone: V2 and V3Complete frame weight with V2 arms: Approximately 49gComplete frame weight with V3 arms: Approximately 51gConstruction: Proprietary carbon-fibre blendStandoffs: 20mm 7075 aluminiumHardware: Grade 12.9 steel screwsArm replacement: Single-screw arm changeMidplate: Offset design for additional ESC, plug and wiring clearanceBattery-strap space: 3mmCompatibility: MS24 and SB24 series componentsCamera compatibility: HDZero Nano, Foxeer Predator and RunCam racing-camera formats Included 1 × MS25 top plate1 × MS25 mid plate1 × MS25 offset plate1 × reinforced carbon battery-strap bracket1 × selected V2 or V3 arm set20mm 7075 aluminium standoffsGrade 12.9 steel frame screwsRequired frame-assembly hardware Select the required V2 or V3 arm version before ordering. Replacement V2 and V3 arms will be available separately. Front and rear carbon braces, electronics, motors, propellers, camera and TPU parts are not included.
DOGCOM 560mAh 150C 3S & 4S FPV Racing LiPo Battery – XT30
The DOGCOM 560mAh 150C LiPo is a compact FPV racing battery available in 3S and 4S versions. Both use an XT30 discharge connector and provide a 150C continuous discharge rating with a 300C maximum rating. Shared specifications Brand: DOGCOMCapacity: 560mAhBattery chemistry: LiPoContinuous discharge rating: 150CMaximum discharge rating: 300CDischarge connector: XT30Application: FPV racing 3S – 11.1V Configuration: 3S1P / 3 cellsNominal voltage: 11.1VEnergy: 6.22WhDimensions: 19.5 × 17 × 65mmWeight: approximately 46gBalance connector: JST-XHRDOGCOM product number: DC007Supplier order code: DC560/150C-3S 4S – 14.8V Configuration: 4S1P / 4 cellsNominal voltage: 14.8VEnergy: 8.29WhDimensions: approximately 63 × 18 × 26mmWeight: approximately 58gSupplier order code: DC560/150C-4S Included 1 × selected DOGCOM 560mAh 150C LiPo battery LiPo safety Charge only with a suitable LiPo balance charger using the correct cell-count setting. Never charge unattended. Do not use a swollen, punctured or damaged battery. Store at the correct storage voltage in a fire-resistant location.
DOGCOM 1550mAh 180C 6S 22.8V HV Series FPV Racing LiPo Battery
The DOGCOM 1550mAh 180C 6S HV Series is a high-voltage LiPo battery designed for professional FPV racing. It delivers 34.41Wh from a compact 33 × 39 × 81mm pack weighing approximately 211g. Specifications Brand: DOGCOMSeries: 180C HV SeriesCapacity: 1550mAhBattery type: High-voltage lithium polymerConfiguration: 6S1P / 6 cellsNominal voltage: 22.8VEnergy: 34.41WhContinuous discharge rating: 180CMaximum discharge rating: 360CDimensions: 33 × 39 × 81mmWeight: approximately 211gDischarge connector: XT60Balance connector: JST-XHRManufacturer number: 8001Application: Professional FPV racing Included 1 × DOGCOM 1550mAh 180C 6S HV Series battery LiPo safety This is a high-voltage LiPo battery. Charge only with equipment and a charging mode suitable for 6S HV LiPo batteries and follow the manufacturer’s limits. Never charge unattended. Do not use a swollen, punctured or damaged battery. Store at the correct storage voltage in a fire-resistant location.
DroneFrames RA35 3.5-Inch FPV Frame Set
The DroneFrames RA35 is a lightweight 3.5-inch carbon-fibre FPV frame designed for compact 4S and 6S builds using 1404 motors.Its individually replaceable, self-bracing 4 mm arms use a single-screw removal system, making damaged arms quick to replace. The frame supports an AIO flight controller or a 20 × 20 mm stack, with separate protection for the main electronics and VTX.SPECIFICATIONSFrame size: 3.5 inchRecommended battery: 4S or 6SRecommended motor size: 1404Electronics mounting: AIO or 20 × 20 mm stackStandoff height: 20 mmArm thickness: 4 mmArm design: Individually replaceable and self-bracingArm removal: Single-screw systemFrame weight: Approximately 33 gFrame material: Carbon fibreHardware: Grade 12.9 steelVTX mounting: Integrated mounting slotsAntenna mounting: TPU or plate-mounted arrangementsINCLUDED1 × top plate1 × main/mid plate1 × bottom plate4 × 4 mm replaceable carbon-fibre armsArm-bracing components20 mm aluminium standoffsGrade 12.9 steel frame hardwareFrame kit only. Motors, electronics, camera, VTX, antenna, propellers, battery and TPU parts are not included.
Panasonic FR 470µF 35V Low-Impedance FPV Capacitors – Pack of 5
Premium genuine Panasonic FR-A 470µF 35V low-impedance aluminium electrolytic capacitors, supplied as a pack of five. Selected by Pure Drone following FPV product testing and evaluation as our preferred compact power-filtering capacitor for reliable 4S and 6S builds.Why FPV drones use a capacitorSoldered across the ESC battery input, the capacitor absorbs short voltage spikes and smooths high-frequency electrical noise produced by the ESC and motors. This can help protect connected electronics, reduce interference in the video feed and provide cleaner power to the flight controller, VTX and camera.Key benefits Low impedance and high ripple-current capability Helps suppress voltage spikes at the ESC battery input Can reduce electrical noise, video interference and power-related instability Compact 10 × 16mm radial package High-reliability Panasonic FR-A series Suitable for correctly installed 4S and 6S FPV builds Specifications Manufacturer: Panasonic Series: FR-A Manufacturer part number: EEUFR1V471 RS stock number: 708-3825 Capacitance: 470µF Rated voltage: 35V DC Maximum impedance: 28mΩ at 100kHz Rated ripple current: 1.79A at 100kHz Capacitance tolerance: ±20% Operating temperature: -40°C to +105°C Dimensions: 10mm diameter × 16mm long Lead pitch: 5mm Mounting: radial through-hole Construction: polarised aluminium electrolytic Country of origin: Malaysia Pack contents: 5 capacitors InstallationThis is a polarised component. The stripe on the body marks the negative terminal. Solder positive to battery positive and negative to battery negative, as close as practical to the ESC battery pads, with the leads kept short and insulated. Reversing polarity can cause the capacitor to fail or vent.A fully charged 6S LiPo is 25.2V, leaving nominal headroom below the capacitor's 35V rating. For unusually long battery leads or exceptionally severe transient conditions, a higher-voltage capacitor may be preferable.
Genuine AMASS XT30U, XT60H, XT90H & MR30 Connectors – Packs of 5 Pairs
Genuine AMASS male and female connector packs for FPV drones, RC models, LiPo batteries, ESCs, motors, chargers and workshop leads. Choose XT30U, XT60H, XT90H or MR30. Every option is supplied as a pack of five complete matching male-and-female connector pairs. XT60H, XT90H and MR30 packs also include the corresponding insulating rear covers.Choose the right connector XT30U: Compact two-pin connector for lightweight FPV and RC power wiring. AMASS rates the cable model to 20A maximum with 16AWG cable under its stated temperature-rise test condition. XT60H: Two-pin main-power connector with rear covers for medium-current battery and ESC installations. Rated to 35A maximum with 12AWG cable under the manufacturer’s test condition. XT90H: Larger two-pin connector for higher-current battery and ESC wiring. Rated to 45A maximum with 10AWG cable under the manufacturer’s test condition. This is the standard XT90H and is not the anti-spark XT90S. MR30: Compact three-pin connector for keeping brushless motor-to-ESC phase connections together. Rated to 20A maximum with 16AWG cable under the manufacturer’s test condition. Shared AMASS specifications 500V DC maximum voltage 100 mating cycles IP40 protection rating -20°C to +120°C working temperature UL94 V-0 flame-retardant housing Gold-plated contacts Solder termination Pack contents XT30U pack: 5 male connectors + 5 female connectors, forming 5 complete pairs XT60H pack: 5 male connectors + 5 female connectors + 10 rear covers, forming 5 complete pairs XT90H pack: 5 male connectors + 5 female connectors + 10 rear covers, forming 5 complete pairs MR30 pack: 5 three-pin male connectors + 5 three-pin female connectors + 10 rear covers, forming 5 complete pairs Installation and safetyThese are solder connectors and require competent installation. Confirm battery polarity before connection and confirm all three motor phases when fitting MR30. Use the appropriate cable gauge and a suitably powerful soldering iron so each joint is completed quickly without overheating the nylon housing. Fully insulate the soldered terminals, keep positive and negative conductors separated, and never solder with a battery connected.Current capability depends on cable gauge, solder quality, ventilation, ambient temperature and installation conditions. Do not exceed the rating of the cable or the weakest component in the power system.
SEQURE H743 MPU6000 4–8S Dual-BEC Flight Controller
The SEQURE H743 is a 4–8S flight controller using a 480MHz STM32H743 processor and MPU6000 gyro. It supports both 20×20mm and 30.5×30.5mm mounting, with eight motor outputs for standard quadcopters and X8 builds. Specifications Processor: STM32H743, 480MHz Gyro: MPU6000 Barometer: BMP280, DPS310 or DPS368, depending on production batch Input voltage: 4–8S LiPo/LiHV BEC outputs: 5V 2.5A and 10V 2A UARTs: 6 Motor outputs: M1–M8 ESC telemetry: RX8 Blackbox: 16MB onboard flash OSD: AT7456E analogue OSD Firmware target: SEQUREH7 Firmware support: Betaflight, INAV and ArduPilot USB: USB-C LED support: WS2812 Mounting: 20×20mm and 30.5×30.5mm, 4mm holes Board size: 36.5 × 36.5 × 6mm Board weight: 7.5g Video-system power The separate 10V 2A BEC can power compatible digital or analogue video equipment, including DJI O3, O4 and O4 Pro systems. Check the connected equipment’s voltage and current requirements before powering it. Included SEQURE H743 flight controller 40mm 30AWG SH1.0-8P double-ended ribbon cable 100mm 30AWG SH1.0-4P cable 5V buzzer with 60mm leads 5 × M3 × 8mm vibration-damping grommets 5 × M3 × 6.6mm vibration-damping grommets Installation: Check the wiring diagram, connector pinout and required output voltage before applying power. Use the SEQUREH7 firmware target.
SEQURE SI012 Pro Max Portable Soldering Iron Kit & TS Replacement Tips
The SEQURE SI012 Pro Max is a compact OLED soldering iron for workshop and field repairs. This listing also includes genuine compatible SEQURE TS replacement tips, so you can choose the complete SI012 Pro Max kit or an individual TS-series spare tip.Choose your item SI012 Pro Max Kit – TS-D24: complete portable soldering iron kit supplied with one TS-D24 tip. TS-D24 Replacement Tip: one compatible replacement tip only. TS-C4 Replacement Tip: one compatible replacement tip only. TS-B2 Replacement Tip: one compatible replacement tip only. SI012 Pro Max specifications Maximum temperature: 450°C / 842°F Power input: USB-C PD3.0, QC2.0, DC 12–25V or 3S–6S LiPo Display: 0.91-inch OLED with adjustable brightness Temperature control: compensation and self-calibration Display options: °C/°F selection and left/right screen rotation Alerts: low voltage, high voltage and high temperature Housing: transparent high-temperature-resistant PC Other functions: adjustable sensitivity, automatic heat-up, power limiting, colour ambient lighting and firmware upgrades Compatible tip families: T12, TS and SI Dimensions with tip fitted: approximately 180 × 16 × 18mm Iron weight with tip: approximately 35g Manufacturer packed weight including outer carton: 240g SI012 Pro Max Kit variant includes 1 × SEQURE SI012 Pro Max soldering iron 1 × TS-D24 soldering tip 1 × soldering-iron stand 1 × storage case 1 × solder wire 1 × XT60-to-DC5525 power cable 1 × hex key with fixing screws Replacement tip informationTS-D24, TS-C4 and TS-B2 are genuine SEQURE replacement tips compatible with the SI012 Pro Max. Each replacement-tip variant contains one tip only. SEQURE states an approximate TS tip length of 103–109mm and describes the tips as using an internal ceramic heating core with the tip and heater integrated.Power and safety noteA mains power supply is not included with the kit. Confirm the polarity and output of any DC, USB-C or battery supply before connection. Disconnect power and allow the tip to cool completely before changing it, and disconnect power when the iron is unattended.
SEQURE MSS12 Pro AC/DC Soldering Station Kit & T12 Replacement Tips
The SEQURE MSS12 Pro is a compact AC/DC soldering station for FPV workshop and field repairs. This listing also includes genuine compatible SEQURE T12 replacement tips, so you can choose the complete MSS12 Pro kit or an individual T12-series spare tip.Choose your item MSS12 Pro Kit – T12-D24: complete soldering station kit supplied with one T12-D24 tip and UK mains lead. T12-B2 Replacement Tip: one conical R0.5 T12 tip only. T12-BC2 Replacement Tip: one 2mm 45° bevel T12 tip only. T12-C4 Replacement Tip: one T12-C4 replacement tip only. T12-D24 Replacement Tip: one 2.4mm chisel T12 tip only. MSS12 Pro specifications Model: MSS12 Pro Included kit tip: T12-D24 Temperature range: 100–450°C / 212–842°F Display: 1.14-inch colour LCD with adjustable brightness and colours AC input: 100–240V USB-C input: PD2.0/3.0 and QC2.0/3.0 DC input: 12–25V Battery input: 3S–6S LiPo via rear XT60 connector Tip compatibility: SEQURE T12-series tips Controls: rotary function knob with °C/°F selection Functions: temperature compensation, self-calibration, buzzer alerts and firmware upgrades Protection: low-voltage, high-voltage and high-temperature warnings Housing: aluminium alloy Manufacturer overall dimensions: 120 × 80 × 30mm Product net weight: 275g MSS12 Pro Kit variant includes 1 × SEQURE MSS12 Pro soldering station 1 × soldering-iron handle 1 × T12-D24 soldering tip 1 × soldering-iron stand with brass tip cleaner 1 × UK mains power lead 1 × storage case 1 × instruction manual Replacement tip information T12-B2: conical tip, R0.5 profile T12-BC2: 2mm bevel tip, 45° profile T12-C4: T12-series C4 replacement tip T12-D24: 2.4mm chisel tip, 0.5mm thickness Overall tip size: 155 × 6.2 × 6.2mm Net tip weight: 8g Maximum stated temperature: 450°C Construction: alloy-plated red copper base with stainless-steel casing Each replacement-tip variant contains one tip only.Compatibility and safetyUSB-C and LiPo power cables are not included. Confirm the supply voltage and connector polarity before use. Disconnect power and allow the tip to cool completely before changing it. SEQURE states that current production units no longer support a custom boot logo.
SEQURE Dry Soldering Iron Tip Cleaner
The SEQURE Dry Soldering Iron Tip Cleaner uses a replaceable metal cleaning-wool insert to remove residual solder and oxidation from soldering iron tips without water. The enclosed holder helps contain loose solder debris and can be opened for cleaning.Specifications Product: Dry soldering iron tip cleaner Manufacturer SKU: PJ0000JZQ Cleaning method: Metal cleaning-wool insert Water required: No Holder: Enclosed two-piece base Net product weight: approximately 103g Manufacturer packed weight: approximately 200g Manufacturer packed dimensions: approximately 130 × 120 × 160mm Included 1 × cleaning holder and base 1 × metal cleaning-wool insert SafetyAllow solder residue to cool before opening or emptying the holder. Wear gloves when replacing the cleaning insert and keep the cleaner upright while opening it.
SEQURE 1–8S LiPo Battery Voltage Tester & Low-Voltage Alarm
The SEQURE 1–8S LiPo Battery Voltage Tester displays total pack voltage and individual cell voltages through a battery’s balance connector. For 2–8S packs, the twin buzzer can also provide an adjustable low-voltage warning.Specifications Battery compatibility: 1–8S LiPo, Li-ion, LiMn and LiFe Low-voltage alarm: 2–8S Alarm setting range: OFF or 2.7–3.8V per cell Default alarm setting: 3.3V per cell Cell-voltage display range: 0.5–4.5V Total-voltage display range: 0.5–36V 1S test-mode range: 3.7–30V Stated voltage accuracy: ±0.01V Alarm indication: twin buzzer and red LED Protection: reverse-polarity protection Dimensions: 40 × 25 × 11mm Net weight: 9g Included1 × SEQURE 1–8S battery voltage tester and low-voltage alarmConnection noteConnect the battery balance plug with its negative wire aligned to the tester’s negative pin. The alarm protects against excessive discharge only when it remains connected and is set appropriately for the battery chemistry and load.
SEQURE Tin Absorber Wire – Copper Desoldering Wick
SEQURE copper desoldering braid for removing excess solder from pads, joints and component leads during FPV electronics repair and rework. Product type: desoldering braid / solder wick Material: braided copper Format: compact spool Use: solder removal and pad clean-up Included1 × spool of tin absorber wirePlace the braid over the solder to be removed and heat through the braid with a soldering iron. Allow the used section to cool before cutting or handling.
Low-Profile M5 Aluminium Flange Nyloc Motor Nuts – Pack of 4
Lightweight low-profile aluminium flange nyloc nuts for FPV drone motors using an M5 × 0.8 threaded prop shaft. At approximately 4.8mm tall, they provide a compact replacement for many standard full-height motor nuts while retaining a nylon locking insert and wide integrated flange. Specifications Product: Low-profile flange nyloc motor nut Thread: M5 × 0.8 internal metric thread Hex size: 8.0mm across flats Flange diameter: 10.8mm Overall height: Approximately 4.8mm Locking system: Nylon insert Material: Aluminium alloy Finish: Colour anodised Pack quantity: 4 matching nuts Colours: Red, blue or gold/yellow Included 4 × matching low-profile M5 flange nyloc motor nuts in the selected colour Compatibility Check the motor shaft before ordering. These nuts require an M5 × 0.8 threaded shaft and will not fit smaller threaded shafts, smooth shafts or alternative prop-retention systems.
Kapton Tape - High Temperature Insulation Tape – 15mm
SEQURE high-temperature insulation tape for FPV electronics, battery work and workshop repairs. The 15mm-wide tape is suitable for insulating and protecting electrical components in applications where heat resistance is important.Specifications Brand: SEQURE Width: 15mm Maximum stated temperature resistance: 180°C Approximate outer roll diameter: 95mm Net weight: 40g Packed weight: approximately 45g Suitable for LiPo and battery wrapping PCB and electronics insulation Electrical repairs Transformers and capacitors Protection boards and workshop use 1 × roll supplied. Roll length is not stated by the manufacturer, so no length specification is claimed on this listing.
VCI 2808 ARES 1350KV FPV Motor
The VCI ARES 2808 1350KV is a high-output 6S brushless FPV motor built for 7-inch racing and Pro Spec-style builds where torque, response and sustained power matter.With a 28 × 8mm stator, 1350KV winding, 52SH arc magnets and a 12S14P configuration, the ARES 2808 is designed for 6S operation. Reference specifications give a 44.04A peak current and 1056.96W maximum instantaneous power, with a 66g weight including the 300mm motor lead.Specifications Brand: VCI Model: ARES 2808 KV: 1350KV Stator: 28 × 8mm Configuration: 12S14P Rated voltage: 6S (24V) Internal resistance: 60mΩ Peak current: 44.04A Maximum instantaneous power: 1056.96W Idle current at 10V: 1.0A Magnets: 52SH arc Motor dimensions: Ø34.5 × 40mm Shaft: M5, 14.6mm length Mounting pattern: 19 × 19mm, 4 × M3 Motor lead: 18AWG silicone, 300mm Weight: 66g including cable Reference performanceReference test data for the 1350KV motor at 24V with a GF/Gemfan 7037-3 propeller reaches approximately 2502g thrust at full throttle, drawing 44.04A and 1056.96W. Actual results vary with propeller, battery, ESC, tune and airframe.In the box 1 × VCI ARES 2808 1350KV motor Mounting screws and prop nut
GEPRC TAKER H60 Mini AM32 60A 4-in-1 ESC
The GEPRC TAKER H60 Mini AM32 is a compact 4-in-1 ESC for 3–8S LiPo FPV builds, rated at 60A continuous with AM32 firmware.SpecificationsESC model: TAKER H60 Mini AM32 60A 4-in-1Input voltage: 3–8S LiPoContinuous current: 60ABurst current: 65A (5s)Protocol: DShot150 / DShot300 / DShot600Firmware: AM32 GEPRC 4IN1 F421Mounting: 20 × 20mmDimensions: 43 × 36mmComponent weight: 17g with aluminium heat sinkImportantConfirm battery voltage, motor load and firmware settings before installation. Fit and test without propellers before first flight.
GEPRC TAKER H743 Mini Flight Controller
The GEPRC TAKER H743 Mini is a 20 × 20mm flight controller for 3–8S FPV builds, using an STM32H743 MCU and ICM42688-P gyro with onboard Bluetooth and dual BEC outputs.SpecificationsMCU: STM32H743Gyro: ICM42688-PInput voltage: 3–8S LiPoFirmware target: GEPRC TAKER H743 MINIBlackbox: 16MB onboard flashOSD: Betaflight OSD, AT7456EBarometer: YesBluetooth: YesUARTs: 7; UART8 reserved for BluetoothBEC: 5V @ 3A and 12V @ 2.5AUSB: Type-CDJI Air Unit connector: Plug & PlayPower filtering: Integrated LC filterMounting: 20 × 20mmDimensions: 31 × 31mmComponent weight: 6.1gImportantCheck the current requirements of connected VTX, receiver and accessories against the 5V and 12V BEC ratings before installation.
GEPRC TAKER F722 35A 32-Bit AIO Flight Controller & ESC
The GEPRC TAKER F722 35A 32Bit AIO combines an STM32F722 flight controller and 35A 32-bit ESC on a compact board for 2–6S FPV builds.SpecificationsMCU: STM32F722Gyro: ICM42688-P (SPI)Firmware target: GEPRC_F722_AIOInput voltage: 2–6S LiPoESC: 32-bit 35AContinuous current: 35ABurst current: 45A (10s)ESC protocols: DShot600, OneShot and MultiShotBlackbox: 16MB onboard flashOSD: Betaflight OSD, AT7456EUARTs: 5BEC: 5V @ 1AUSB: Type-CBuzzer output: YesLED output: YesMounting: 25.5 × 25.5mmDimensions: 35 × 33.5mmComponent weight: 9.3gIncluded1 × TAKER F722 35A AIO1 × XT30 18AWG 7cm lead1 × 35V 220µF capacitor1 × SH1.0-6-pin cable8 × M2 × 6.5mm dampening ballsImportantCheck motor current draw and accessory power requirements against the 35A ESC and 5V/1A BEC ratings before installation.
GEPRC O4 Series Step-Down BEC
The GEPRC O4 Series Step-Down BEC is a compact regulator for powering DJI O4 Air Unit and O4 Air Unit Pro systems from 3–6S LiPo builds.SpecificationsInput voltage: 10.5–25.2V (3–6S LiPo)Output voltage: 9V / 5VDefault output: 9V5V selection: Bridge the 5V padDimensions: 17 × 8.3mmComponent weight: 1gCompatible video systems: DJI O4 Air Unit and DJI O4 Air Unit ProConversion type: Step-down onlyIncluded1 × O4 Series Step-Down BEC1 × 6-pin 6-wire cable1 × 6-pin 4-wire cableImportantConfirm the selected output voltage and wiring polarity before connecting the O4 Air Unit. Do not exceed 25.2V input.
GEPRC Smoke Stopper XT30 / XT60
The GEPRC Smoke Stopper is an inline current-protection tool for checking newly built or repaired FPV electronics before direct battery connection, with both XT30 and XT60 connectors.SpecificationsInput voltage: 1–6S LiPo / 3–30VTrip current: 1.0AHold current: 0.5AShort-circuit trip time: approximately 3msOvercurrent trip time: approximately 10msConnectors: XT30 and XT60, input and outputComponent weight: 13.6gImportantUse during initial power-up and fault checking. This is a current-protection aid and cannot prevent every type of electrical damage; correct wiring and continuity checks are still required.
GEPRC ELRS Nano DUAL 2.4G C3 True Diversity Receiver
The GEPRC ELRS Nano DUAL 2.4G C3 is a compact ExpressLRS true-diversity receiver using dual SX1281 RF chips and two antennas for 2.4GHz FPV control links.SpecificationsMCU: ESP32-C3RF chips: 2 × SX1281Firmware: GEPRC Nano True Diversity 2.4GHz RXFrequency: 2.4GHz ISMRefresh rate: 25–1000HzTelemetry power: 10mWOperating voltage: 5VCrystal oscillator: TCXOAntenna connectors: 2 × IPEX1Indicator: RGB LEDDimensions: 17 × 13mmReceiver weight: 1.1gIncluded1 × GEPRC ELRS Nano DUAL 2.4G receiver2 × 2.4G T-antennas, IPEX1, 80mm1 × SH1.0 4-pin 100mm receiver cable1 × heat-shrink tube1 × user manualImportantUse the correct ExpressLRS firmware target and verify binding, failsafe and antenna installation before flight.
RED WOLF Flame-Retardant Wiring Harness Tape – 19mm × 15m (1 Roll)
RED WOLF self-adhesive fabric harness tape for protecting, bundling and tidying wiring on FPV builds, battery leads, workshop electronics and automotive looms. The polyester non-woven fabric uses a strong acrylic adhesive and is hand-tearable for quick installation.Specifications Brand: RED WOLF Type: Self-adhesive fabric wiring harness tape Colour: Black Width: 19mm / 3/4in Length: 15m / approx. 50ft Material: Polyester non-woven fabric Adhesive: Acrylic pressure-sensitive adhesive Temperature range: -40°C to 105°C Flame-retardant: self-extinguishing within approximately 30 seconds Hand tearable: Yes Included1 × roll of RED WOLF wiring harness tapeUseful for cable wrapping, wiring looms, battery leads and general workshop cable management.
HGLRC KRATOS Fireproof LiPo Battery Bag – 80 × 120 × 180mm
HGLRC KRATOS compact LiPo battery safety bag for charging, storage and transport. HGLRC lists an 80 × 120 × 180mm size, 125g product weight and an outer PVC mesh layer, with fire-resistant, water-resistant and battery-protection functions.Specifications Brand: HGLRC Model: KRATOS Type: LiPo battery safety bag Dimensions: 80 × 120 × 180mm Weight: 125g Outer material: PVC mesh Closure: zippered lid Carry handle: yes Manufacturer-listed functions: fire resistance, water resistance and lithium battery protection Included1 × HGLRC KRATOS battery safety bagSafety note: A battery safety bag can add a layer of protection around LiPo batteries but cannot eliminate fire risk. Charge and store LiPo batteries using appropriate supervision and safe procedures.
HGLRC Kevlar Battery Strap – 250mm
HGLRC Kevlar battery-retention strap for securing LiPo packs on FPV builds. Available in two widths at 250mm length, with a lightweight construction and high-grip woven material.Specifications Brand: HGLRC Material: Kevlar Length: 250mm 15 × 250mm weight: 6g 20 × 250mm weight: 8.3g Available sizes 15 × 250mm 20 × 250mm Select the width that best suits the battery and frame layout.
HGLRC 60A 4-in-1 MINI 8S 32-bit V1 ESC – BL32
Compact HGLRC 60A 4-in-1 MINI 8S 32-bit V1 ESC in the BL32 version, designed for high-voltage FPV builds using a 20 × 20mm mounting pattern.Specifications Brand: HGLRC Model: 60A 4IN1 MINI 8S 32-bit V1 ESC Version: BL32 Input voltage: 3–8S LiPo Continuous current: 60A per channel Peak current: 65A per channel for 10 seconds MCU: QF32MTF4AK8U7 Telemetry: Supported Protocols: DShot300, DShot600, Oneshot, PWM Mounting pattern: 20 × 20mm, M3 Dimensions: 46.8 × 34 × 6.5mm Weight: 14g This listing is specifically for the BL32 version. HGLRC states that firmware revisions can change between production batches, so the exact BL32 revision should be checked on receipt before flashing or updating.
HGLRC SPECTER F722 Lite Flight Controller – ICM42688P, ELRS 2.4GHz
Compact HGLRC SPECTER F722 Lite flight controller with an STM32F722 MCU, ICM42688P gyro and integrated ExpressLRS 2.4GHz receiver for 2–6S FPV builds.Specifications Brand: HGLRC Model: SPECTER F722 Lite Flight controller firmware: HGLRCF722MINI_4.5.1 MCU: STM32F722 Gyro: ICM42688P Barometer: DPS310 Input voltage: 2–6S LiPo (8.4–25.2V) BEC: 5V 2A Blackbox: 16MB UARTs: 5 Built-in receiver: ELRS 2.4GHz R2 OSD: Supported Mounting pattern: 20 × 20mm, M3 Dimensions: 28 × 28mm Weight: 4g Included 1 × SPECTER F722 Lite flight controller FC connection cable 2.4GHz antennas Soft-mount hardware
HGLRC F722 40A AIO V2 Flight Controller & ESC – 2–6S BL32
HGLRC F722 40A AIO V2 combines an STM32F722 flight controller and 32-bit 40A ESC on a compact 34 × 34mm board for 2–6S FPV builds.Specifications Brand: HGLRC Model: F722 40A AIO V2 Flight controller target: HGLRC_F722_S Flight controller firmware version: 2025.12 MCU: STM32F722 Gyro: ICM42688P Blackbox: 16MB OSD: Supports analogue and digital signal BEC: 5V 2A ESC firmware: BL32 32.10 Input voltage: 2–6S LiPo (8.4–25.2V) Continuous current: 40A per channel Peak current: 60A per channel Quad-channel peak current: 140A Mounting pattern: 25.5 × 25.5mm, M2 Dimensions: 34 × 34mm Weight: 10.5g Manufacturer application: 2–5 inch FPV frames
HGLRC LED Mini FPV Lighting System – Controller or 38mm RGB LED Set
Compact HGLRC LED Mini lighting options for FPV builds. Choose the LED Mini Controller for controlling compatible RGB lighting, or the lightweight 38mm RGB LED set for adding bright programmable lighting to your quad.Choose your typeLED Mini Controller 2–6S input (7.4–25V) One-click mode switching Reserved pads for LED connections Supports direct control and flight-controller/remote adjustment Electronic switch function Dimensions: 17 × 12.5 × 6.5mm Controller weight: 1.47g Included: 1 × LED Mini Controller and 4 × 30AWG 100mm connecting wires (red, black, yellow and green).LED Mini 38mm RGB Set – 4 Pack 5V input 12 × RGB2020 LEDs per strip Dimensions per strip: 38 × 7.1 × 5mm Weight per strip: 0.7g 70mm connection leads Compact, lightweight design for FPV builds Included: 4 × HGLRC LED Mini 38mm strips and 4 × connecting leads.
TrueRC CORE 5.8 U.FL RHCP Antenna – 45mm
TrueRC CORE 5.8 is a compact omnidirectional 5.8GHz circularly polarised FPV video antenna for direct U.FL connection to compatible VTX hardware. This 45mm version keeps the antenna cable short for compact FPV builds while retaining the durable polycarbonate CORE housing.Specifications Frequency: 5.8GHz Polarisation: RHCP Connector: U.FL Cable length: 45mm Gain: 1.9dBic Bandwidth: 5.5–6.7GHz Cross-polar rejection: −10 to −20dB Radiation efficiency: 98% SWR: ≤1.2:1 Antenna head: 16.9mm diameter × 13.1mm height Weight: approximately 2.3g Housing: durable polycarbonate Country of origin: Canada CompatibilityManufacturer-listed compatibility includes Caddx Vista / RunCam Link, DJI Air Unit O3, DJI Air Unit O4 and Walksnail Avatar HD VTX. Always confirm connector type and antenna polarisation match your equipment before use.Included1 × TrueRC CORE 5.8 U.FL RHCP antenna, 45mm, in the selected colour
TrueRC CORE 5.8 U.FL RHCP Antenna – 85mm
TrueRC CORE 5.8 is a compact omnidirectional 5.8GHz circularly polarised FPV video antenna for direct U.FL connection to compatible VTX hardware. This 85mm version provides additional cable length for larger frames or installations where the antenna needs to be positioned further from the VTX while retaining the durable polycarbonate CORE housing.Specifications Frequency: 5.8GHz Polarisation: RHCP Connector: U.FL Cable length: 85mm Gain: 1.9dBic Bandwidth: 5.5–6.7GHz Cross-polar rejection: −10 to −20dB Radiation efficiency: 98% SWR: ≤1.2:1 Antenna head: 16.9mm diameter × 13.1mm height Weight: approximately 2.5g Housing: durable polycarbonate Country of origin: Canada CompatibilityManufacturer-listed compatibility includes Caddx Vista / RunCam Link, DJI Air Unit O3, DJI Air Unit O4 and Walksnail Avatar HD VTX. Always confirm connector type and antenna polarisation match your equipment before use.Included1 × TrueRC CORE 5.8 U.FL RHCP antenna, 85mm, in the selected colour
TrueRC Singularity 5.8 Stubby SMA RHCP Antenna
TrueRC Singularity 5.8 Stubby is a compact 5.8GHz circularly polarised omnidirectional FPV antenna with a hardened polycarbonate housing. The low-profile SMA format is well suited to FPV goggles and receiver modules that use a standard SMA connector, including HDZero-compatible hardware listed by TrueRC.Specifications Frequency: 5.8GHz Polarisation: RHCP Connector: SMA Gain: 1.9dBic Bandwidth: 5.6–6.0GHz Cross-polar rejection: −15 to −30dB Radiation efficiency: 99% SWR: ≤1.5:1 Weight: 3.7g Dimensions: 12.7mm diameter × 20mm height Housing: hardened polycarbonate Colour: Red Country of origin: Canada CompatibilityTrueRC lists compatibility with HDZero Goggles and HDZero VRX4. Check that your hardware uses a standard SMA connector and RHCP before ordering.Included1 × TrueRC Singularity 5.8 Stubby SMA RHCP antenna – Red
T-Motor F1404 4600KV Brushless FPV Motor
The T-Motor F1404 4600KV is a compact 1404 brushless FPV motor for lightweight 3-inch racing and TinyTrainer builds, as well as 2.5-inch cinewhoops. The 4600KV version is manufacturer-listed at 9.34g including its motor lead.Specifications Brand: T-Motor / T-Hobby Model: F1404 KV: 4600KV Colour: Gray + Red Stator size: 1404 Rated voltage: 3–4S LiPo Configuration: 9N12P Motor dimensions: 17.9 × 16.6mm Shaft diameter: 1.5mm Motor lead: 24AWG, 150mm Weight: 9.34g including cable Idle current: 0.6A Internal resistance: 138mΩ Maximum power: 316W (manufacturer 60-second figure) Peak current: 20A (manufacturer 60-second figure) Country of origin: China Included 1 × T-Motor F1404 4600KV brushless motor 1 × fixing hardware kit, including socket-head motor mounting screws
Pure Drone Clear Double-Sided Nano Tape – 1mm × 5m
Built for FPV battery grip: Apply this nano tape to the battery mounting area of the carbon top/bottom plate to create a tacky, high grip surface under the LiPo. Used with a proper battery strap, it helps stop the battery sliding or shifting during hard acceleration, rapid direction changes and crashes. Clear double-sided nano tape supplied in 5 metre rolls for mounting, securing and workshop use. The tape is washable, reusable and removable on suitable smooth surfaces, with a transparent finish for discreet fixing. Specifications Type: Double-sided nano adhesive tape Colour: Clear / transparent Thickness: 1mm Roll length: 5m Available widths: 10mm and 20mm Washable: Yes Reusable: Yes Removable: Yes Included 1 × 5m roll of clear double-sided nano tape in the selected width