Search: “GEPRC”
Searching the Pure Drone catalogue…
GEPRC ELRS Nano DUAL 2.4G C3 True Diversity Receiver
The GEPRC ELRS Nano DUAL 2.4G C3 is a compact ExpressLRS true-diversity receiver using dual SX1281 RF chips and two antennas for 2.4GHz FPV control links.SpecificationsMCU: ESP32-C3RF chips: 2 × SX1281Firmware: GEPRC Nano True Diversity 2.4GHz RXFrequency: 2.4GHz ISMRefresh rate: 25–1000HzTelemetry power: 10mWOperating voltage: 5VCrystal oscillator: TCXOAntenna connectors: 2 × IPEX1Indicator: RGB LEDDimensions: 17 × 13mmReceiver weight: 1.1gIncluded1 × GEPRC ELRS Nano DUAL 2.4G receiver2 × 2.4G T-antennas, IPEX1, 80mm1 × SH1.0 4-pin 100mm receiver cable1 × heat-shrink tube1 × user manualImportantUse the correct ExpressLRS firmware target and verify binding, failsafe and antenna installation before flight.
GEPRC O4 Series Step-Down BEC
The GEPRC O4 Series Step-Down BEC is a compact regulator for powering DJI O4 Air Unit and O4 Air Unit Pro systems from 3–6S LiPo builds.SpecificationsInput voltage: 10.5–25.2V (3–6S LiPo)Output voltage: 9V / 5VDefault output: 9V5V selection: Bridge the 5V padDimensions: 17 × 8.3mmComponent weight: 1gCompatible video systems: DJI O4 Air Unit and DJI O4 Air Unit ProConversion type: Step-down onlyIncluded1 × O4 Series Step-Down BEC1 × 6-pin 6-wire cable1 × 6-pin 4-wire cableImportantConfirm the selected output voltage and wiring polarity before connecting the O4 Air Unit. Do not exceed 25.2V input.
GEPRC Smoke Stopper XT30 / XT60
The GEPRC Smoke Stopper is an inline current-protection tool for checking newly built or repaired FPV electronics before direct battery connection, with both XT30 and XT60 connectors.SpecificationsInput voltage: 1–6S LiPo / 3–30VTrip current: 1.0AHold current: 0.5AShort-circuit trip time: approximately 3msOvercurrent trip time: approximately 10msConnectors: XT30 and XT60, input and outputComponent weight: 13.6gImportantUse during initial power-up and fault checking. This is a current-protection aid and cannot prevent every type of electrical damage; correct wiring and continuity checks are still required.
GEPRC TAKER F722 35A 32-Bit AIO Flight Controller & ESC
The GEPRC TAKER F722 35A 32Bit AIO combines an STM32F722 flight controller and 35A 32-bit ESC on a compact board for 2–6S FPV builds.SpecificationsMCU: STM32F722Gyro: ICM42688-P (SPI)Firmware target: GEPRC_F722_AIOInput voltage: 2–6S LiPoESC: 32-bit 35AContinuous current: 35ABurst current: 45A (10s)ESC protocols: DShot600, OneShot and MultiShotBlackbox: 16MB onboard flashOSD: Betaflight OSD, AT7456EUARTs: 5BEC: 5V @ 1AUSB: Type-CBuzzer output: YesLED output: YesMounting: 25.5 × 25.5mmDimensions: 35 × 33.5mmComponent weight: 9.3gIncluded1 × TAKER F722 35A AIO1 × XT30 18AWG 7cm lead1 × 35V 220µF capacitor1 × SH1.0-6-pin cable8 × M2 × 6.5mm dampening ballsImportantCheck motor current draw and accessory power requirements against the 35A ESC and 5V/1A BEC ratings before installation.
GEPRC TAKER H60 Mini AM32 60A 4-in-1 ESC
The GEPRC TAKER H60 Mini AM32 is a compact 4-in-1 ESC for 3–8S LiPo FPV builds, rated at 60A continuous with AM32 firmware.SpecificationsESC model: TAKER H60 Mini AM32 60A 4-in-1Input voltage: 3–8S LiPoContinuous current: 60ABurst current: 65A (5s)Protocol: DShot150 / DShot300 / DShot600Firmware: AM32 GEPRC 4IN1 F421Mounting: 20 × 20mmDimensions: 43 × 36mmComponent weight: 17g with aluminium heat sinkImportantConfirm battery voltage, motor load and firmware settings before installation. Fit and test without propellers before first flight.
GEPRC TAKER H743 Mini Flight Controller
The GEPRC TAKER H743 Mini is a 20 × 20mm flight controller for 3–8S FPV builds, using an STM32H743 MCU and ICM42688-P gyro with onboard Bluetooth and dual BEC outputs.SpecificationsMCU: STM32H743Gyro: ICM42688-PInput voltage: 3–8S LiPoFirmware target: GEPRC TAKER H743 MINIBlackbox: 16MB onboard flashOSD: Betaflight OSD, AT7456EBarometer: YesBluetooth: YesUARTs: 7; UART8 reserved for BluetoothBEC: 5V @ 3A and 12V @ 2.5AUSB: Type-CDJI Air Unit connector: Plug & PlayPower filtering: Integrated LC filterMounting: 20 × 20mmDimensions: 31 × 31mmComponent weight: 6.1gImportantCheck the current requirements of connected VTX, receiver and accessories against the 5V and 12V BEC ratings before installation.